Uniden Bearcat Bc125at Driver For Mac

  1. Uniden Bearcat Bc125at Driver For Mac Download
  2. Uniden Bearcat Bc125at Driver For Mac Windows 10
  3. Uniden Bearcat Bc125at Driver For Mac Drivers

Step by step instructions for installing USB drivers and Uniden SS software on a Windows XP laptop for use with a Uniden BC125AT scanner. Scanner Software Download, select your scanner model or software product: Uniden BC125AT and UBC125XLT AE125H and UBC126: ARC125 V2.1 build 2 for Uniden BC125AT, UBC125XLT, UBC126 and AE125H (includes drivers).

Front Panel


Contains the LCD, keys and speaker.
Some of the keys have two functions, their normal function and a alternate function depending on which screen is being displayed (which mode the radio is in).
Fig 1



The knob also has a push button function whose function also depends on the mode of the radio. In most modes pressing the knob will change it's function to a Volume control. At other times it's equivalent to pressing Enter (PgmE). This later use allows you to both navigate through a menu and make selections using only the knob, very handy.

Top Panel


BNCf Antenna connecotr
3.5mm mono headphone jack
Selection Knob-Button
Fig 7 Top

Right Panel


USB Mini computer & Charging cable
Fig 8 Right Side


Uniden bearcat bc125at driver for mac windows 10

Rear Panel


Battery Compartment

Battery Type switch
(Alkaline or Ni-MH rechargeable)
Belt Clip
Label
Fig 6 Rear Panel

Bottom Panel

The bottom has feet so that the radio will stand up.

Function Menus

Note that the Func (Orange) key is a precursor key to the keys with an orange notation as shown in the below function table.

Function Table

Uniden Bearcat Bc125at Driver For Mac
Func
then
Menu
Hold
Close Call (Mode, Bands, Alert, Scan Hits, Set Delay, CTCSS/DECS Search, Review Lockouts, Exit)
Pri/1
Priority (Off, DND, Scan, Plus, Exit)
Wx
Weather (Scan, Standby, Priority, Delay, Exit)
Svc
Service Search (1: Police, 2: Fire/Em, 3: Ham, 4:Marine, 5:Railroad, 6: Civil Air, 7:Mil Air, 8:CB, 9:FRS/GMRS/MURS, 0:Racing)
Pressing any of the numbers 0 - 9) during Service Search will toggle Off or On that service.
Beep/7
Toggle Key Beep On/Off
L/O
Toggle Keypad Lockout
PgmE
Scanning (Save Feq, Program Limits, Set Delay, CTCSS/DCS Search, Review Lockouts, Exit)
On/Off
Misc (Backlight, Contrast, Charge Time, Exit)
Scroll
Button
Set Squelch by rotating Scroll knob

Banks

The bank numbers at the bottom of the LCD screen can have two different meanings.

When in Service Scan (FuncSrch/Svc) the numbers show the type of service being looked for.
(1: Police, 2: Fire/Em, 3: Ham, 4:Marine, 5:Railroad, 6: Civil Air, 7:Mil Air, 8:CB, 9:FRS/GMRS/MURS, 0:Racing)
Pressing any of the numbers 0 - 9) during Service Search will toggle Off or On that service.

In most cases they refer to groups of 50 Channels. There's no requirement that a bank be inside any frequency range, modulation type &Etc. You can use they as you will. A common use is to put similar types of frequencies together, for example State VHF low band FM highway patrol, VHF & UHF FM sheriff and local police all in one bank. So if you're going to fill in the banks by the type of service then it would be a good idea to use the existing bank numbering, i.e. Bank1 for police, &Etc.

Power Up Options

To turn on: Press and keep down the On/Off button.
To turn off: Press and keep down the On/Off button.

Press and keep down 1 while powering up = USA Band Plan
Press and keep down 2 while powering up = Canadian Band Plan
Press and keep down 29Hold while powering up = Reset
After I reset the radio and power it on with an external antenna connected it goes directly to my local weather broadcast.

Computer

Installing the file BC125AT_SS_V1_03_00 loads the program but not the USB driver.


The driver file BC125AT_CDC_XP.inf needs to be placed in the C:WINDOWSINF folder.
Now when the radio is connected by USB cable the New Hardware Wizard finds the radio and installs the driver.

In My ComputerPropertiesHardwareDevice Manager the BC125AT shows up with a COM port number
21 in my case.

After starting the BC125AT SS program go to ToolsCOM port setting and use Auto Detect or manually set
the COM port number. Auto worked for me.

Here's the Bank 1 display after Reset & I've only entered a local 2 meter ham frequency.
To get this this display use: ScannerRead from Scanner.

Bearcat

Front Panel


Contains the LCD, keys and speaker.
Some of the keys have two functions, their normal function and a alternate function depending on which screen is being displayed (which mode the radio is in).
Fig 1



The knob also has a push button function whose function also depends on the mode of the radio. In most modes pressing the knob will change it's function to a Volume control. At other times it's equivalent to pressing Enter (PgmE). This later use allows you to both navigate through a menu and make selections using only the knob, very handy.

Top Panel


BNCf Antenna connecotr
3.5mm mono headphone jack
Selection Knob-Button
Fig 7 Top

Right Panel


USB Mini computer & Charging cable
Fig 8 Right Side


Rear Panel


Battery Compartment

Battery Type switch
(Alkaline or Ni-MH rechargeable)
Belt Clip
Label
Fig 6 Rear Panel

Bottom Panel

The bottom has feet so that the radio will stand up.

Function Menus

Note that the Func (Orange) key is a precursor key to the keys with an orange notation as shown in the below function table.

Function Table

Func
then
Menu
Hold
Close Call (Mode, Bands, Alert, Scan Hits, Set Delay, CTCSS/DECS Search, Review Lockouts, Exit)
Pri/1
Priority (Off, DND, Scan, Plus, Exit)
Wx
Weather (Scan, Standby, Priority, Delay, Exit)
Svc
Service Search (1: Police, 2: Fire/Em, 3: Ham, 4:Marine, 5:Railroad, 6: Civil Air, 7:Mil Air, 8:CB, 9:FRS/GMRS/MURS, 0:Racing)
Pressing any of the numbers 0 - 9) during Service Search will toggle Off or On that service.
Beep/7
Toggle Key Beep On/Off
L/O
Toggle Keypad Lockout
PgmE
Scanning (Save Feq, Program Limits, Set Delay, CTCSS/DCS Search, Review Lockouts, Exit)
On/Off
Misc (Backlight, Contrast, Charge Time, Exit)
Scroll
Button
Set Squelch by rotating Scroll knob

Banks

The bank numbers at the bottom of the LCD screen can have two different meanings.

When in Service Scan (FuncSrch/Svc) the numbers show the type of service being looked for.
(1: Police, 2: Fire/Em, 3: Ham, 4:Marine, 5:Railroad, 6: Civil Air, 7:Mil Air, 8:CB, 9:FRS/GMRS/MURS, 0:Racing)
Pressing any of the numbers 0 - 9) during Service Search will toggle Off or On that service.

In most cases they refer to groups of 50 Channels. There's no requirement that a bank be inside any frequency range, modulation type &Etc. You can use they as you will. A common use is to put similar types of frequencies together, for example State VHF low band FM highway patrol, VHF & UHF FM sheriff and local police all in one bank. So if you're going to fill in the banks by the type of service then it would be a good idea to use the existing bank numbering, i.e. Bank1 for police, &Etc.

Bc125at

Power Up Options

To turn on: Press and keep down the On/Off button.
To turn off: Press and keep down the On/Off button.

Press and keep down 1 while powering up = USA Band Plan
Press and keep down 2 while powering up = Canadian Band Plan
Press and keep down 29UnidenHold while powering up = Reset
After I reset the radio and power it on with an external antenna connected it goes directly to my local weather broadcast.

Uniden Bearcat Bc125at Driver For Mac Download

Computer

Installing the file BC125AT_SS_V1_03_00 loads the program but not the USB driver.


Uniden Bearcat Bc125at Driver For Mac Windows 10

The driver file BC125AT_CDC_XP.inf needs to be placed in the C:WINDOWSINF folder.
Now when the radio is connected by USB cable the New Hardware Wizard finds the radio and installs the driver.

In My ComputerPropertiesHardwareDevice Manager the BC125AT shows up with a COM port number
21 in my case.

After starting the BC125AT SS program go to ToolsCOM port setting and use Auto Detect or manually set
the COM port number. Auto worked for me.

Here's the Bank 1 display after Reset & I've only entered a local 2 meter ham frequency.
To get this this display use: ScannerRead from Scanner.

Uniden Bearcat Bc125at Driver For Mac Drivers